The tree in Prestige saddles has been designed to adapt perfectly to the horse and to maintain the best seat for the rider. Made of a special mix of fibres, it is at least 1 kg lighter than traditional saddles and needs no metal reinforcement.
This saddle has advantages over those made of natural materials, like wood.
Though wood is elastic, it still has “life” in it. For this reason
as atmospheric conditions change and the years go by the characteristics of the wood change, becoming less stable and less resistant.
The Prestige tree, on the other hand, was purpose designed to provide the same elasticity as one made of wood while, at the same time, ensuring maximum stability over time. It is no chance matter that it offers a lifetime’s guarantee, except in the
case of an accident.
In addition, the width of a Prestige saddle can always be altered. It can be narrowed
or widened, depending on the shape of the horse, without having to take the saddle
apart. For this reason even when the shape of the horse changes the product remains
CORRECTLY POSITIONING THE SADDLE
The saddle must be positioned in such a way that there is enough space between
the shoulder and the saddle so that shoulder movement is not restricted . The
way to do this is to run the end of your hand over the shoulder of the horse
until you detect the scapula bone. Allow for a minimum width of about four fingers
and that is the place to position the saddle. This will leave a space, the width
of the palm of your hand, between the scapula and the girth. Remember that the
front part of a jumping saddle could project upfront the shoulder of the horse
but the fixed part, the tree, must never do so.
FIVE CARDINAL RULES
1 - Tree size: If a saddle is correctly positioned the tree will extend parallel
to the back of the horse and as close as possible to it.
2 - Consideration for the horse’s backboneA and withers: The width between
the saddle panels must make proper allowance for the horse’s spine and
not bear down on it under the weight of the rider. The size of the front arch
of the saddle must be such as to enable compliance with the age-old “4-fingers”
rule (corresponding to about 5 cm) between the pommel and the withers of the
3 - Balancing: Once the right tree size has been found, the next step is to
ensure the saddle is properly balanced. When it rests in position, the saddle
must conform to the horse’s back in a way that evenly distributes the
weight of the rider over the entire surface and so prevents it bearing down
too much to the front (the scapula bones of the horse) or to the back (the loins
of the horse).
4 - Contact by the panels: The panels must, in their entirety and along their
full length, form a snug fit with the horse’s back. This will ensure proper
distribution of the weight of the rider.
5 - Symmetry: Look at the horse from the rear and check that the saddle rests
parallel to the backbone of the horse and is positioned symmetrically about
it If the saddle complies with these five rules it will be properly positioned
and be comfortable for the horse.
MADE TO MEASURE SADDLES
Prestige Italia has developed a way of measuring a horse’s back
that is unique and absolutely innovative. It enables the exact morphological
features of a horse to be transferred onto paper by using a withers gauge. This
special rod-shaped instrument is able to maintain whatever shape it is bent
into and is notched for measuring purposes.
Prestige also uses a special level that finds the exact point at which the horse’s
backbone is horizontal. In this way panels can be made that are customised to
The aim is to make higher or lower panels that ensure the rider has the proper
balance in the saddle.
Made-to-measure saddles for horses: the technical characteristics.
Because panels can be made with increased or reduced thickness horses can be
fitted with saddles perfectly adapted to their individual morphology.
Made-to-measure saddles for riders: The technical characteristics show how Prestige
can make saddles to measure for riders, too. All of its saddles (except the
TREKKER models) have 5 flap lengths: from XS to XXL. Its show jumping saddles
have, in addition, 3 flap projection sizes: standard, +2 cm, +4 cm.
They also have large, medium-sized, or small blocks to suit your style of riding.
All models in the “PREMIUM” line are available in black, tobacco
brown, or cognac.
Seat sizes are 16”, 17”, and 18” except for the following
models: Atena and Atena Flaps (just 17” and 18”). Joy Jumper and
Lucky Dressage (just 16”), and the Trekker saddle line, which has just
a standard seat and width size. Width sizes vary between 29 and 37, with the
exception of the following saddles: D1, D1D, D1 K, D1D K, SALAMANCA, ICELAND
D1, ATENA SFC and ATENA SFC FLAPS, which
offer a more restricted size range: S – M – L.
The leather used in Prestige Italia products is naturally tanned and originates
from cattle bred outdoors.
Any slight shadow, differences or markings are not faults but guarantees of
a natural product.
All Prestige Italia saddles come with a lifetime guarantee against any damage
to the tree (apart from any accident).
The leather and stitching is guaranted for two years from date of manufacture.
Do not use rigid stirrup leathers, which can damage surfaces. Prestige’s
nonstretch are excellent and soft and have the slimmest on the market.
Be careful with boots that incorporate rubber or coarse material. They accelerate
the wear on calfskin-lined saddle flaps through rubbing up against them.
Saddles which have flaps made from calf skin leather provide instant softness
along with additional grip, therefore this must be taken into consideration
as it is not as durable as traditional saddle leather.
The leather, which is used for the panels and the girths, is treated with an
antisweat process, thus reducing the amount of maintenance required and reinforcing
strength within these areas.
We do not recommend using hard leather stirrup leathers as this will only damage
the saddle. Therefore, we recommend that A17 soft leathers be used. This will
prolong the life of the saddle.
The tree, which is constructed using various fibres, does not require any metal
support. The withers bar can be altered using one of our machines without dismantling
This allows the saddle width to be changed every time your horse changes shape.
“Special” versions of lined saddles are so called due to the presence
of added material in leather on the lower part of the flap exposed to contact
with the stirrup leathers.
SADDLES WITH FLOCKED PANELS
Panels flocked with a special synthetic fibre that prevents compression of the
material and therefore requires less maintenance. These panels are especially
suited to horses that are asymmetric between their front and back or vice versa.
They also offer more options: panels +1 cm / +2 cm at the back or with half
SADDLES WITH LATEX PANELS
These soft-latex panels have reduced weight in the area of the withers and shoulders.
This allows greater freedom of movement when airborne during jumping, so avoidAing
pressure on the withers.
Panels with increased-thickness at the back or half-thickness panels are available
for horses that are asymmetrical from front to back and vice versa.
SF CONCEPT LATEX SADDLES
These special panels are designed to give freedom to the trapezius muscle and,
by the same token, leave the shoulders unhampered. They are especially suited
to stallions or horses with less developed shoulders.
(Available only for 17” and 18” seats).
| femur measure
Relation between femur’s length and the flaps’ length; the femur’s
length has to be
taken on the internal side of the leg from the groin to the top of the knee.
| flap’s sizes for jumping saddles
In case of longer flaps these are little bit more forward on the front.
| Seat size
These sizes don’t work with riders that are more than 120 kg.
| Withers bar
Withers bar from 29 to 37. Each withers bar size is 1 cm more or less with
to the standard size (32).